您的位置: 标准下载 » 国内标准 » 行业标准 »

DL/T 618-1997 气体绝缘金属封闭开关设备现场交接试验规程

时间:2024-05-21 18:38:02 来源: 标准资料网 作者:标准资料网 阅读:9841
下载地址: 点击此处下载
基本信息
标准名称:气体绝缘金属封闭开关设备现场交接试验规程
英文名称:Code for hand-over test of gas-insulated metal-enclosed switchgear on site
中标分类: 电工 >> 输变电设备 >> 高压开关设备
替代情况:被DL/T 618-2011代替
发布部门:中华人民共和国电力工业部
发布日期:1997-08-04
实施日期:1997-12-01
首发日期:1900-01-01
作废日期:2011-11-01
提出单位:中国电力企业联合会标准化部
归口单位:电力工业部气体绝缘金属封闭电器标准化技术委员会
起草单位:广东电力试验研究所、电力工业部电力科学研究院
起草人:钟定珠、陈锦清、郭碧红、秦维陶、冯水华
出版社:中国电力出版社
出版日期:1997-12-01
页数:8页
适用范围

本规程适用于额定电压72.5 kV及以上、频率为50Hz的户内和户外安装的气体绝缘金属封闭开关设备(GIS)现场交接验收试验。72.5kV以下的GIS可参考本规程。

前言

没有内容

目录

没有内容

引用标准

没有内容

所属分类: 电工 输变电设备 高压开关设备
基本信息
标准名称:内六角平端紧定螺钉
英文名称:Hexagon socket set screws with flat point
中标分类: 机械 >> 通用零部件 >> 紧固件
ICS分类: 机械系统和通用件 >> 紧固件 >> 螺栓、螺钉、螺柱
替代情况:替代GB/T 77-1985;被GBT 77-2007代替
发布部门:国家质量技术监督局
发布日期:2000-09-02
实施日期:2001-02-01
首发日期:1958-10-07
作废日期:2007-12-01
主管部门:中国机械工业联合会
归口单位:全国紧固件标准化技术委员会
起草单位:机械委标准化所
出版社:中国标准出版社
出版日期:2004-04-22
页数:平装16开/页数:/字数:
书号:155066.2-13865
适用范围

本标准规定了螺纹规格为M1.6~M24、性能等级为45H、A1、A2、CU2、CU3和AL4、产品等级为A级的内六角平端紧定螺钉。如需其他技术要求,应从现行标准(如GB/T 196、GB/T 3106和GB/T 3098.3)中选择。

前言

没有内容

目录

没有内容

引用标准

没有内容

所属分类: 机械 通用零部件 紧固件 机械系统和通用件 紧固件 螺栓 螺钉 螺柱
Product Code:SAE J1204
Title:Wheels-Recreational and Utility Trailer Test Procedure
Issuing Committee:Wheel Standards Committee
Scope:This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway use on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose vehicles. (See Figures 1 and 2.) For procedures and minimum performance requirements for wheels used on trucks, see SAE J267, and for wheels used on passenger cars, see SAE J328. For the application of passenger car and light ruck wheels [inset less than 0.10 m (0.33 ft)] to this trailer service, use this procedure. For the application of heavier truck wheels [inset 0.10 m (0.33 ft) or mre] use SAE J267. Mobile home service is outside the scope of this document.There are two basic test procedures described, a cornering fatigue test and radial fatigue test. The cornering test is directed at the wheel disc; whereas the radial test also examines the rim and attachment portion of the wheel. Both test procedures are required to obtain a thorough examination of the wheel.